Portable CD Player
Audio
AX
AX
AX
2100
2101
2102
AX
AX
AX
5100
5101
5102
AX
AX
AX
5103
5104
5113
Portable CD Player
English
Français
Español
Nederlands
Meet Philips at the Internet
CLASS 1
LASER PRODUCT
AX2100 AX5100 AX5103
AX2101 AX5101 AX5104
AX2102 AX5102 AX5113
3140 115 2876.1
Printed in China
POWER SUPPLY / GENERAL INFORMATION
English
CONTROLS / POWER SUPPLY
CONTROLS ( see figure
1
)
ECO-PLUS NiMH battery information (for versions supplied with the
rechargeable ECO-PLUS NiMH battery AY 3362)
1 OPEN 2 ..............opens the CD lid
Recharging works only on players supplied with the rechargeable ECO-PLUS
NiMH battery AY 3362.
2 9.........................stops CD play, clears a program or switches the player off
3 ∞ .......................skips and searches CD tracks backwards
4 2; ......................switches the player on, starts or pauses CD play
5 § .......................skips and searches CD tracks forwards
Recharging the ECO-PLUS NiMH battery on board
1
Insert the rechargeable ECO-PLUS NiMH battery AY 3362.
2
Connect the mains adapter to the 4.5V DC socket of
the player and then to the wall socket.
6 DBB.....................switches the bass enhancement on and off. This button also
switches acoustic feedback (the beep) on/off when it is
pressed for more than 2 seconds
y
is pulsing.
7 ............................display
•
Recharging stops after a maximum of 7 hours, or when you start playback.
8 PROGRAM ..........programs tracks and reviews the program
3
When the battery is fully recharged,
FULLappear briefly in the display,
before the display switches off.
and
9 MODE .................selects the different playing possibilities: SHUFFLE,
SHUFFLE REPEAT ALL, REPEAT, REPEAT ALL and SCAN
0 RESUME .............stores the last position of a CD track played
HOLD...................locks all buttons
OFF......................switches RESUME and HOLD off
Notes: – It is normal for the batteries to become warm
during recharging.
– If the batteries become too warm, recharging will be interrupted for
approximately 30 minutes and Hotis displayed.
– To ensure proper recharging on board, take care that contacts are
clean.
! LINE OUT/p........3.5 mm headphone socket, socket to connect the player to
another audio input of an additional appliance, remote
control socket (not on all versions)
@ VOL E ............adjusts the volume
# 4.5V DC...............socket for external power supply
$ ............................belt clip holder
– Use only the ECO-PLUS NiMH battery AY 3362.
Handling instructions
•
Recharging already charged or half-charged batteries will shorten their
lifetime. We therefore recommend that you let the rechargeable ECO-PLUS
NiMH battery run till it is completely empty before you recharge it.
% ............................typeplate
•
•
To avoid a short circuit, do not let the battery touch any metal object.
If the battery becomes empty soon after recharging, then either its contacts
are dirty or it has reached the end of its lifetime.
This set complies with the radio interference requirements of the
European Community.
Batteries (supplied or optionally available)
Mains adapter (supplied or optionally available)
You can use the following batteries with this CD-player:
Use only the AY 3170 adapter (4.5 V / 300 mA direct
current, positive pole to the center pin). Any other product
may damage the player.
•
•
normal batteries type LR6, UM3 or AA (preferably Philips), or
alkaline batteries type LR6, UM3 or AA (preferably Philips).
V
DC
1
Make sure the local voltage corresponds to the power
adapter’s voltage.
Notes:– Old and new or different types of batteries should not be combined.
– Remove batteries if they are empty or if the player is not going to be used for
a long time.
2
Connect the power adapter to the 4.5V DC socket of
the player and to the wall socket.
Inserting batteries
Note: Always disconnect the adapter when you are not using it.
1
2
Push OPEN 2 to open the CD lid.
Belt Clip (not on all versions)
Open the battery compartment and insert either 2
normal or alkaline batteries, or the rechargeable
NiMH battery AY3362 (if supplied).
1
To attach the belt clip to the CD-player, position the
shaped grip (found on the back of the belt clip) so
that it fits into the belt clip hole of the CD-player.
BELT CLIP
Battery indication
2
3
Turn the clip to LOCK as indicated on the set.
The approximate power level of your batteries is shown in the display.
Battery full
To detach, gently lift the belt clip and turn
to RELEASE as indicated on the set.
Battery two-thirds full
Battery one-third full
LOCK
LIFT
Battery dead or empty. When the batteries are dead
RELEASE
or empty, the symbol
flashes, bAttis
displayed, and the beep tone sounds repeatedly.
Average playing time of batteries under normal conditions
Battery type
Normal
ESP on
5 hours
5 hours
20 hours
22 hours
9 hours
Power Save
6 hours
Environmental information
AX 21XX
AX 51XX
AX 21XX
AX 51XX
•
•
All redundant packing material has been omitted. We have done our utmost to
make the packaging easily separable into two mono materials: cardboard (box)
and polyethylene (bags, protective foam sheet).
6 hours
Alkaline
22 hours
25 hours
10 hours
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packing materials, exhausted batteries and old equipment.
Rechargeable ECO-PLUS NiMH battery
Batteries contain chemical substances, so they should be disposed
of properly.
GENERAL INFORMATION
CD PLAY
CD player and CD handling
Playing a CD
E
L
BL
TIB
I
A
P
M
O
C
•
•
Do not touch the lens A of the CD player.
This CD-player can play all kinds of Audio Discs such
as CD-Recordables and CD-Rewritables. Do not try to
play a CD-ROM, CDi, VCD, DVD or computer CD.
E COMP
L
ABL
IT
R
W
E
R
D
CD REWRIT
Do not expose the unit, batteries or CDs to humidity,
rain, sand or excessive heat (caused by heating
equipment or direct sunlight).
You can clean the CD player with a soft, slightly
•
•
•
EN
P
O
dampened, lint-free cloth. Do not use any cleaning
agents as they may have a corrosive effect.
1
2
Push the OPEN 2 slider to open the player.
VOL.
0
To clean the CD, wipe it in a straight line from the
Insert an audio CD, printed side up, by pressing the
CD onto the hub.
center toward the edge using a soft, lint-free cloth. A cleaning agent may
damage the disc! Never write on a CD or attach a sticker to it.
The lens may cloud over when the unit is moved suddenly from cold to warm
surroundings. Playing a CD is not possible then. Leave the CD player in a warm
environment until the moisture has evaporated.
B
B
D
3
4
Close the player by pressing the lid down.
K
C
A
R
T
E
D
O
M
Press 2; to switch the player on and start playback.
yThe current track number and elapsed playing
time are displayed.
E
D
O
M
•
•
Active mobile phones in the vicinity of the CD player may cause malfunctions.
Avoid dropping the unit as this may cause damage.
AM
R
ROG
P
Headphones HE205
•
You can pause playback by pressing 2;.
yThe time at which playback was paused starts
flashing.
•
Connect the supplied headphones to the LINE OUT/p
socket of the player.
•
You can continue playback by pressing 2; again.
Note: LINE OUT/p can also be used for connecting the
player to your HiFi system (with a signal lead) or to
your car radio (with a cassette adapter or signal
lead). In both cases, the volume of the player must
be set to position 8.
5
Press 9 to stop playback.
yThe total number of tracks and the total playing
time of the CD are displayed.
6
Press 9 again to switch the player off.
IMPORTANT!
Hearing safety: Do not play your headphones at a high volume. Hearing experts advise
that continuous use at high volume can permanently damage your hearing.
Traffic safety: Do not use headphones while driving a vehicle. It may create a hazard
and it is illegal in many countries. Even if your headphones are an open-air type
designed to let you hear outside sounds, do not turn up the volume so high that you
cannot hear what is going on around you.
•
To remove the CD, hold it by its edge and press the
hub gently while lifting the CD.
Note: If there is no activity, the set will automatically
switch off after a while to save energy.
In-car use (connections supplied or optionally available)
Playback information
•
•
If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded
Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 118 71890) car voltage
converter (4.5 V DC, positive pole to the centre pin) and the AY 3501 car adapter
cassette. Any other product may damage the set.
properly, nF dISCis displayed, indicating that the CD has not been
finalized. In that case, use FINALIZE on your CD recorder to complete the
recording.
1
Put the set on a horizontal, vibration-free and
stable surface. Make sure it is in a safe place,
where the set is neither a danger nor an
obstacle to the driver and the passengers.
When playing a CD-Rewritable (CD-RW), please note that it takes 3–15
seconds after pressing 2; for sound reproduction to start.
12 V DC
•
•
Playback will stop if you open the CD lid.
B
B
D
While the CD is read, 1-:-flashes in the display.
4,5 V DC
K
C
A
TR
2
Plug the voltage converter into the
cigarette lighter socket (only for 12 V car
battery, negative grounding), then connect
the wired end with 4.5V DC input socket on the
set.
E
D
O
M
E
S
T
D
O
M
B
O
O
S
A
S
M
RA
IC
AM
B
RO
G
N
DY
P
L
A
I
T
I
G
E
D
I
B
L
TI
B
L
E
P
P
A
M
E
CO
CO
L
B
A
IT
R
WW
E
R
E
D
CD
R
O
F
F
•
R
E
S
U
M
E
Volume and bass
•
H
O
L
D
L
I
N
E
P
E
N
O
O
U
T
/
VOL.
Volume adjustment
Adjust the volume by using VOL E.
•
3
4
If necessary, clean the cigarette lighter socket to obtain a good electrical
contact.
Turn down the volume and connect the adapter cassette plug to LINE OUT/p
on the set.
Bass adjustment
•
Press DBB to switch the bass enhancement on or
off
B
B
D
5
6
7
Carefully insert the adapter cassette into the car radio’s cassette compartment.
Make sure the cord does not hinder your driving.
y
is shown if the bass enhancement is
activated.
K
C
A
R
T
E
D
O
M
E
D
O
M
Set VOL E on the set to position 8. Start playback on the set and adjust
M
RA
G
O
R
P
the sound with the car radio controls.
•
Always remove the voltage converter from the cigarette lighter socket
when the set is not in use.
Remote control (supplied or optionally available)
Note: If your car radio has a LINE IN socket, it is better to use it for the
car radio connection instead of the adapter cassette. Connect the signal
lead to this LINE IN socket and to LINE OUT/p on the set.
Use the AY 3767 or AY 3768 cord remote control.The buttons on the remote
control have the same functions as the corresponding buttons on the set.
1
2
3
Press 9 twice to switch off the set.
Firmly connect the remote control to LINE OUT/p on the set.
Adjust the volume VOL E on the CD player and remote control.
FEATURES
FEATURES
Selecting a track and searching
Selecting a track during playback
Selecting different playing possibilities−MODE
It is possible to play tracks in random order, to repeat a single track or the entire
CD, and to play the first few seconds of each track.
•
Briefly press ∞ or § once or several times to skip to
the current, previous or next track.
B
B
D
1
Press MODE during playback as often as required in
order to activate one of the following ‘modes’. The
active mode is shown in the display.
ys h u ffl e : All tracks of the CD are played in
random order until all of them have been played
once.
ys h u ffl e re p e a t a ll : All tracks of the CD
are played repeatedly in random order.
yrepeat : The current track is played repeatedly.
B
B
K
C
D
yPlayback continues with the selected track, and
the track’s number is displayed.
A
R
T
E
D
O
M
K
C
A
R
T
E
OD
M
E
D
O
M
AM
R
G
O
R
P
Selecting a track when playback is stopped
E
D
O
M
1
Briefly press ∞ or § once or several times to select
the desired track. The track number is displayed.
M
RA
OG
R
P
2
Press 2; to start CD play.
yPlayback starts with the selected track.
yrepeat all : The entire CD is played repeatedly.
ySCAN: The first 10 seconds of each of the
Searching for a passage during playback
shuffle repeat all
remaining tracks are played in sequence.
1
Keep ∞ or § pressed to find a particular passage in
a backward or forward direction.
2
Playback starts in the chosen mode after 2 seconds.
ySearching starts while playback continues at low
volume. After 2 seconds the search speeds up.
•
To return to normal playback, press MODE repeatedly until the display shows
no active modes.
ESP / Power Save Mode
2
Release the button when you reach the desired passage.
yPlayback continues from this position.
With a conventional portable CD-player you might have experienced that the
music stopped e.g. when you were jogging. The Electronic Skip Protection
prevents loss of sound caused by light vibrations and shocks. Continuous playback
is ensured. However ESP does not prevent playback interruptions during vigorous
running. It also does not protect the unit against any damage caused by dropping!
On this set ESP is default on. It is possible to set ESP off and enter the Power
Save mode. The Power Save mode (PS; Power Save) helps to extend battery
lifetime for longer playback.
Notes: – If the player is in SCAN mode (see MODE chapter), searching is not
possible.
– In shuffle, shuffle repeat all or repeat mode (see MODE chapter), or
while playing a program, searching is only possible within the
particular track.
•
Press MODE for more than 2 seconds.
y
disappears.
•
Press MODE again for more than 2 seconds.
yPSis displayed once
ESP on ➟ ESP off ➟ Power Save ➟ESP on
Programming track numbers
RESUME and HOLD
B
D
You can interrupt playback and continue (even after an
extended period of time) from the position where
playback stopped (RESUME) and you can lock all buttons
of the set so that no action will be executed (HOLD).
Use the RESUME–HOLD–OFF slider for these functions.
You can store up to 30 tracks to play in a program.
A single track may be stored more than once in the
program.
K
C
A
R
T
E
D
O
M
E
D
O
M
M
A
1
While playback is stopped, select a track with
R
G
O
R
P
∞ or §.
RESUME – continuing from where you have stopped
2
Press PROGRAM to store the track.
yp ro g ra m lights up; the track number
programmed and Pwith the total number of
stored tracks are displayed.
1
Switch the slider to RESUME during playback to activate RESUME.
yre s u m e is shown.
program
program
2
3
Press 9 whenever you want to stop playback.
Press 2; whenever you want to resume playback.
3
4
Select and store all desired tracks in this way.
resum e
yre s u m e is shown and playback continues
from where you have stopped.
Press 2; to start playback of your selected tracks.
yp ro g ra m is shown and playback starts.
•
To deactivate RESUME, switch the slider to OFF.
yre s u m e goes off.
•
You can review the program by pressing PROGRAM
for more than 2 seconds.
yThe display shows all the stored tracks in sequence.
HOLD – locking all buttons
You can lock the buttons of the set by switching the slider to HOLD. Now, when a
key is pressed, no action will be executed. This is of use, for example, when
transporting the player in a bag. With HOLD activated, you can avoid accidental
activation of other functions.
Notes: – If you press PROGRAM and there is no track selected, SELis
displayed.
– If you try to store more than 30 tracks, FULLis displayed.
1
Switch the slider to HOLD to activate HOLD.
yAll buttons are locked. HoLdis shown when
you press any button. If the set is switched off,
h o ld will be shown only when 2; is pressed.
Clearing the program
resum e
•
While playback is stopped, press 9 to clear program.
yCLris displayed once, p ro g ra m goes off,
and the program is cleared.
hold
program
2
To deactivate HOLD, switch the slider to OFF.
Note: If you deactivate HOLD by switching the slider to RESUME, you will be
activating the RESUME function.
Note: The program will also be cleared if the power supply is interrupted, or if
the CD-player lid is opened, or if the set switches off automatically.
TROUBLESHOOTING
Troubleshooting
WARNING: Under no circumstances should you try to repair the set yourself as
this will invalidate the warranty. If a fault occurs, first check the points listed,
before taking the unit for repair. If you are unable to solve a problem by following
these hints, consult your dealer or service center.
The CD player has no power, or playback does not start
•
Check that your batteries are not dead or empty, that they are inserted
correctly, that the contact pins are clean.
•
•
Your adapter connection may be loose. Connect it securely.
For in-car use, check that the car ignition is on. Also check player’s batteries.
The indication no diSCis displayed
•
•
Check that the CD is clean and correctly inserted (label-side upward).
If your lens has steamed up, wait a few minutes for this to clear.
The indication nF diSCis displayed
CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
•
The indication HOLD is on and/or there is no reaction to controls
•
•
If HOLD is activated, then deactivate it.
Electrostatic discharge. Disconnect power or remove batteries for a few seconds.
The CD skips tracks
•
•
The CD is damaged or dirty. Replace or clean the CD.
RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on.
Troubleshooting
No sound or bad sound quality.
•
•
•
•
PAUSE might be active. Press 2;.
Loose, wrong or dirty connections. Check and clean connections.
Volume might not be appropriately adjusted. Adjust the volume.
Strong magnetic fields. Check player’s position and connections. Also keep
away from active mobile phones.
•
For in-car use, check that the cassette adapter is inserted correctly, that the car
cassette player’s playback direction is correct (press autoreverse to change),
and that the cigarette lighter jack is clean. Allow time for temperature change.
CAUTION
Use of controls or adjustments or performance of procedures other than
herein may result in hazardous radiation exposure or other unsafe
operation.
|